Search Results

A study was conducted to reduce unburned oil fractions in diesel particulate matter (PM) by improving oil consumption. A method utilizing radioisotope 14C was developed to measure the unburned oil fractions separately for the four paths by which oil is consumed: valve stem seals, piston rings, PCV system, turbocharger. The conversion ratio of oil consumption to PM was calculated by comparing the unburned oil emission rates with oil consumption rates, which were obtained by the use of the 35S tracer method. The result in an experimental diesel engine shows the highest conversion ratio for the oil leaking through the valve stem seals. The modifications to the engine were thereby focused on reducing the leakage of the stem seals. This stem seal modification, along with piston ring improvements, reduced oil consumption, resulting in the unburned oil fractions in PM being effectively reduced.

The object of this study is to investigate the possibility of improving ride comfort, and develop a new damping control system. We supposed and analyzed the ideal damping control for vehicle suspension system using optimal control strategy. The parameter study shows the effect of reducing vehicle acceleration from road excitation. To achieve the same performance with a more simple and lower cost control strategy, we introduce another control strategy called ‘Skyhook model’ proposed by D.Karnopp. Continuously damping control system is developed based on this to avoid some problems that might be caused in the case of a two-stage switching system. Further more, variable control gain depends on vehicle vibration circumstances introduced to realize the adaptation of various road conditions. Using computer simulation and testing the experimental vehicle, effectiveness of this system is evident and the possibility of ride comfort improvement is verified by using this control.

A new heating strategy for electrically heated catalysts has been developed which reduces power consumption while achieving the desired hydrocarbon conversion. The relationship between catalyst volume and power consumption is presented. Observations of catalytic reactions by a thermoviewer camera and mathematical simulations are used to optimize the heating pattern. Significant reductions in power consumption, while maintaining conversion efficiency, are reported by heating only the front face of the catalyst. However, prior to mass production additional work is required to improve durability, and reliability and to resolve manufacturing issues.

Toyota Motor Corporation has recently developed a new six-speed automatic transmission (A761E) for Front Engine Rear Wheel Drive (FR) vehicles. Following the general trend of increased shift stages and a wider range of gear ratios, this six-speed automatic transmission has been developed with attention paid to the gear steps and a wider range of gear ratios. By balanced selection of close-ratio gears in a wider range, the change greatly improves the power performance and fuel economy of the vehicle. To further improve fuel economy we have adopted new technologies such as low-viscosity ATF, neutral control, and deceleration control by extending the fuel cut range (reset speed). We have also adopted a flat-shaped torque converter, small solenoids, an aluminum oil pump cover, etc. to realize the lightest six-speed automatic transmission in the world.

Contribution to carbon neutrality is one of the most important challenges for the automotive industry. As CO2 emission has been reduced through electrification such as hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV), internal combustion engines (ICEs) equipped in those powertrain systems are still necessary for the foreseeable future, and continuous efforts to improve fuel efficiency are demanded. To improve powertrain thermal efficiency, direct-injection turbocharged gasoline engines have been widely utilized in recent years. Super lean-burn combustion engine has been researched as a next generation of turbocharged gasoline engines. Further utilization of turbochargers is expected. Compared with turbocharged downsized gasoline engines available in the current market, much higher boost pressure must be utilized to realize the super lean-burn engines. As a result, compressor housing temperature will be very high compared with the current market one.

The noise generation mechanism of a direct-acting valve train such as used in sporty and luxury cars was determined for both mechanical and hydraulic tappets through measurements of sound pressure levels and vibrations and the use of computer graphics to observe actual valve and tappet movement. Two phenomena were clarified: chatter at low engine speeds and a mechanical noise at high engine speeds. Further experiments established that the noise of a mechanical tappet can be greatly reduced and its tonal quality improved by optimizing the cam profile and by increasing the acoustic damping ratio of the tappet.

Recently, the smokeless rich diesel combustion had been demonstrated [1]. This can realize smokeless and NOx-less combustion by using a large amount of cooled EGR under a near stoichiometric and even in a rich operating condition. We focus on the effects of reducing diesel combustion temperature on soot reduction.

The new Toyota FCV “Mirai” has reduced the weight, size, and cost of the high-pressure hydrogen storage system while improving fueling performance. The four 70 MPa tanks used on the 2008 Toyota FCHV-adv were reduced to two new larger diameter tanks. The laminated structure of the tanks was optimized to reduce weight, and a high-strength low-cost carbon fiber material was newly developed and adopted. The size of the high-pressure valve was reduced by improving its structure and a high-pressure sensor from a conventional vehicle was modified for use in a high-pressure hydrogen atmosphere. These innovations helped to improve the weight of the whole storage system by approximately 15% in comparison with Toyota FCHV-adv, while reducing the number of component parts by half and substantially reducing cost. The time required to fuel the FCV was greatly reduced by chilling the filling gas temperature at the hydrogen filling station to −40°C (as per SAE J2601).

The newly-developed 2JZ engine series is available in two types; a naturally aspirated 2JZ-GE and a turbo charged 2JZ-GTE. Both have in-Line-6 cylinder arrangement and displacement volume of 2.997 liters and have attained many features expected for the engines of new era by utilizing new technologies, such as DOHC 4 valve, high compression ratio, a highly rigid structural design which is realized by extensive use of the CAE, a serpentine accessory drive belt, and auto tensioners for timing belt and accessory belt systems. These engines are stroke up versions of the 1JZ engines. The 2JZ-GE engine, which has been developed for the SC300, delivers high performance of 169 KW/6000rpm and 284 Nm/4800rpm by adopting a variable induction system, a knock-control system with two sensors, etc. The other type, the 2JZ-GTE engine which has been developed for the Aristo in japan includes a TWO-WAY-TWIN-TURBO’ system equipped with ceramic turbine wheels.

A new hybrid transmission has been developed for all-wheel-drive (AWD) cars, and is used in the new Lexus LS600h and LS600hL for its first application. It has a compact layout consisting of a power-split device, generator, high-output electric motor, and a two-stage speed reduction device. Combined with a 5-liter V-8 engine, it achieves power performance rivaling 6-liter engine vehicles, the fuel efficiency of a medium-class vehicle, and outstanding quietness. This paper describes the structure, performance, and shift control technology of this hybrid transmission.

Efficiency of Driveshafts have not been analyzed in great detail in the past due to their relatively high efficiency. However, it is possible to obtain about a 0.1 percent increase in fuel economy by decreasing driveshaft torque losses by about 20 percent, owing to the combination mode fuel calculation. In order to improve fuel economy it is necessary to increase the efficiency of the constant velocity universal joint (C.V.J.) used for driveshafts. Additionally, propeller shafts with improved heat characteristics are required. It is for these reasons that this project is conducted. In this paper, the motion of two typical joint used for front-engine, front-drive passenger cars is analyzed geometrically and efficiency formulas are derived. One of the joints is a Rzeppa joint, used on the wheel side of the driveshaft and the other is a tripot joint, used on the differential side. These formulas are then verified by experiment.

For the launch of the redesigned Lexus LS, a new 3.5 L V6 twin turbo engine has been developed aiming at unparalleled performance on four axes, “driving pleasure”, “power-performance”, “quietness” and “fuel economy”. To achieve outstanding power-performance and high thermal efficiency, the specifications have been optimized for high speed combustion. The maximum torque of 600 Nm, power of 310 kW (yielding specific power of 90 kW/L), and the maximum thermal efficiency of 37% have been achieved using several new technologies including a high efficiency turbocharger. A prototype vehicle equipped with this engine and Direct-Shift 10AT achieved a 0-60 mph acceleration time of 4.6 sec, with extremely good CAFE combined fuel economy of 23 mpg and power-performance aligned with V8 turbocharged offerings from competing OEM’s.